Colonial Doll Outfit for N.'s Doll

I made a matching doll outfit for N's doll for N's Colonial Day at school.  The kids learned what life was like in the early days of America.  They learned to weave on a 4-shaft table loom and also to weave a tape (strap or band) on a  reproduction Colonial tape loom.  The boys made a simple wooden top, and the girls made a sock doll.  They played school with little slates and learned about manners and rules of the 18th Century.  They also learned how to put quilt fabric squares into a colorful quilt block.  They churned butter, made corn muffins, and also made fresh-squeezed lemonade.  A fun day!  The kids all looked so cute in their Colonial outfits.

                                                     N's Colonial Doll Outfit, March 2017

N's doll dress is based on Simplicity 8211, v. 4-5. 

Doll Dress Notes
 I added length to the dress so it is floor length.  I made a placket at the back neck instead of using Velcro for the back seam.  The placket is 1 1/2" wide, and I used the straight grain of fabric.  I used a 3/8 inch seam. Sew the back seam up to placket. Press seams open.  Staystitch the opening 3/8" at top to V--one stitch at bottom, pivot and back up the other side.

Slit opening is 4 1/4" from raw edge. Sew placket Right Sides together, with the placket on top. Press, and then sew the folded edge of placket by hand, and then baste the right placket back.   I could make the pattern have side seams instead of a back seam so the placket is easier without seam there (just cut a slit).  (Placket width is usually 2 seam allowances plus twice the width of placket. One side is pressed under the width of seam allowance, 3/8".)  

The Yoke back seam is stitched when sewing the neck seam of yoke.  Trim, clip, and turn. Interface the yoke facing. I used snaps for the back neck edge. I used Peter Rabbit character buttons on the front of the dress to match N's.

                                                 N's Colonial Doll Dress Simplicity 8211

The doll's apron and bonnet pattern are from Little House Pioneer Doll Dress and Ensemble by Ethington House Heritage Doll Clothing.

The Apron
I used Apron View A.  I added facings to the back edges of the apron facing pattern and made the curve a bit more gentle on the facings so it was easier to serge that edge.  I interfaced the facings. I took off 1" from the pattern length and added a ruffle to match N's pinafore. I cut the ruffle 3 1/2" wide (1/2 inch doubled hem and 1/2" seam, so about 2 1/2" finished).  I used two pieces 35" long.  Seam is in the center.  Ruffle is 2 1/2 times fullness.

Notes: Open out lower facing and pin ruffle in place up to the seam of the lower facing.  Fold the facing around to the outside and sew it in place.  Serge the whole edge.  Fold back the facing to the inside and press seam allowances to the pinafore.  Tack the facings to the seam allowances and catch stitch or whip stitch the facing to the underarm seams.

I had added 1/4" to the back edges of the apron so I could make buttonholes.  I used Peter Rabbit buttons, which are almost 5/8" long, so buttonholes are 3/4" long.  On most garments, the Center Front or Center Back is 5/8" from the finished edge, and the buttonhole starts 1/8" closer to the finished edge, so 1/2" from the finished edge. I sewed the doll buttonholes about 3/8" + from the finished side edge, 5/8" from the top finished edge, and 6/8" from the lower finished edge.  Buttonholes are on the Right back.  I used Two Buttonholes.

                                                   N's Doll Bonnet, Little House Pioneer

The Bonnet
The bonnet is a bit confusing at the casing.  I reinforced the corners where the slit will be on the bonnet near the casing.  The casing must be just under the slit, so the facing ends just at the casing.  I added to the seams of the bonnet to make it easier to sew and added to the facing edge where it folds over.  Press that folded edge so it has a crease mark. 

When sewing the bonnet facing to the bonnet, right sides together, sew from just at the bottom of the casing around to the bottom of the casing at the other side.  Turn and press.  (The top part of the facing is not sewn yet.)  Cut a slit to the reinforcing stitches from each of the side edges.  Fold in the side raw edges of the casing, and put the elastic in place.  The elastic is cut longer with the 5" center marks in the center of it.  It's easier to sew it in flat and stretch it later to the markings. Sew down the top of the facing, carefully making sure to not catch the elastic in the seam.  Sew next to the elastic at the bottom of the casing--about a 1/2" casing.  Then pull the elastic to the 5" measurement marks and sew the side edges well, making sure the sides of the fabric are turned inside the casing.  Use matching thread. Sew the ties about 1/4" above the slit on the right side of the bonnet with the seam of the tie down.  When sewing the bonnet facing to the bonnet, make sure the bonnet edge is about 1/16" inside the facing brim edge so it's easier to turn the brim and hand sew that edge. Sew the side seams down when sewing (catch them in the seam). I made the ties longer so it's easier for her to tie the bow.  They are 1 1/4" x 18" cut.  I interfaced the brim of the bonnet.

The Colonial Rules from early America were posted for the kids to see.